Cmod S7-25 Out-Of-Box Demo (Under Construction)
This page is part of the 2020.1 updates, which are currently underway. Refer to Cmod S7-25 Out-Of-Box Demo for the latest official version of this page.
This project is a a simple Vivado demo using the Cmod S7-25's LEDs, RGB LED, buttons, and USB-UART bridge, written in Verilog. When programmed onto a Cmod S7, the demo will cycle the board's RGB LED from Blue to Green to Red to Black. The other LEDs will light up in sequence.
To use the USB-UART bridge feature of this demo, the Cmod S7 must be connected to a serial terminal on the computer it is connected to over the MicroUSB cable. Whenever one of the two buttons is pressed, “Button # Pressed!” is sent to the computer using the USB-UART bridge.
- Cmod S7-25 with a MicroUSB Programming Cable
- Vivado Installation compatible with the latest release of this demo (2020.1)
- See Installing Vivado, Vitis, and Digilent Board Files for instructions on how to install Vivado.
- Serial Terminal application to receive messages printed by the demo
- See Installing and Using a Terminal Emulator for more information.
Download and Usage Instructions
First and foremost, releases are only compatible with the version of the Xilinx tools specified in the release version number. In addition, releases are only compatible with the specified variant of the board. For example, a release tagged “20/DMA/2020.1” for the Zybo Z7 is only to be used with the -20 variant of the board and Xilinx tools of version 2020.1.
The latest release tag for this demo is highlighted in green, and release candidates (which may not be fully tested, and should be used at your own risk, are highlighted in yellow.
Important: The setup instructions found in this section only pertain to the latest release.
Note: Releases for FPGA demos from before 2020.1 used a different git structure, and used a different release tag naming scheme.
|Release Tag||Release Downloads||Setup Instructions|
|25/OOB/2020.1-1||Release ZIP downloads||See Below|
|v2018.2-2||Release ZIP downloads||v2018.2-2 README|
|v2017.4-1||Release ZIP downloads||v2017.4-1 README|
Note: All demos for the Cmod S7 are provided through the Cmod-S7 repository on Github. Further documentation on the structure of this repository can be found on this wiki's Digilent FPGA Demo Git Repositories page
Instructions on the use of the latest release can be found in this dropdown:
- Using the Latest Release
Note: This workflow is common across many Digilent FPGA demos. Screenshots may not match the demo you are working with.
Important: These steps are only to be used with releases for Xilinx tools versions 2020.1 and newer. Older releases may require other flows, as noted in the table of releases.
First, download and extract the '*.xpr.zip' file from the demo release page, linked above.
- Open a Vivado Project from a Release
Select the dropdown corresponding to your operating system, below.
- Build a Vivado Project
Generate a Bitstream
In order to create a file that can be used to program the target board, each stage of the “compilation pipeline” needs to be run.
This starts with Synthesis. Synthesis creates a description of the logic gates and connections between them required to perform the functionality described by the HDL files, given the constraints included in XDC files. To run Synthesis click either in the toolbar or in the Flow Navigator. The output of Synthesis is then passed to Implementation.
Implementation has several steps. The steps that are always run are Opt Design (Optimize the design to fit on the target FPGA), Place Design (Lay out the design in the target FPGA fabric), and Route Design (Route signals through the fabric). To run Implementation click either in the toolbar or in the Flow Navigator. This output is then passed on to the Bitstream Generator.
The Bitstream Generator generates the final output file needed for programming the FPGA. To run Bitstream Generation click either in the toolbar or in the Flow Navigator. With no settings changed, the generator will create a '.bit' file.
Depending on the complexity of the design, the board used, and the strength of your computer, the process of building the project can take between 5 and 60 minutes. When complete, a pop up dialog will appear, prompting you to select one of several options. None are relevant for the purposes of this guide, so click Cancel. The “write_bitstream complete” status message can be seen in the top right corner of the window, indicating that the demo is ready to be deployed to your board.
- Set up the Cmod S7
Plug your Cmod S7 into your computer via the MicroUSB programming cable. Connect it to a serial terminal application with a baud rate of 9600.
- Program a Bitstream onto an FPGA Board
Vivado's Hardware Manager can be opened by clicking on Open Hardware Manager at the bottom of the Flow Navigator pane on the left side of the Vivado window.
The first step to programming a device is to connect the Vivado Hardware Server to it as a target. To get to the Open Hardware Target wizard click the link in the green banner near the top of the window. From the drop-down that opens, select .
Once the wizard opens, click Next.
The next screen asks if the hardware server is local or remote. If the board is connected to the host computer choose local, if it is connected to another machine choose remote and fill in the Host Name and Port fields.
Click Next to continue.
This screen gives a list of devices connected to the hardware server. If there is only one connected it will be the only device shown.
Click Next to continue.
The final screen shows a summary of the options selected in the wizard. Verify the information and click Finish. The board is now connected to the hardware server.
To program the device with the bit file generated earlier, either click the link in the green banner at the top of the window or click the button in the Flow Navigator under . From the drop-down that opens, select the device to program (Example: ) and the following window will open:
The Bitstream File field should be automatically filled in with the bit file generated earlier. If not, click the button at the right end of the field and navigate to
<Project Directory>/<Project Name>.runs/impl_1/ and select the bit file (Example: ). Now click Program. This will connect to the board, clear the current configuration, and program it using the new bit file.
At this point, the demo is now running on your Cmod S7. Refer to the Description section of this document for more information on what it does.
All materials related to the use of the Cmod S7 can be found on its Resource Center.
For a walkthrough of the process of creating a simple HDL project in Vivado, see Getting Started with Vivado for Hardware-Only Designs. Information on important parts of the GUI, and indirect discussion of the steps required to modify, rebuild, and run this demo in hardware can also be found here.
For technical support, please visit the FPGA section of the Digilent Forum.