SRAM to DDR Component

Download

Description

Note: There is a problem mapping the MIG in ISE. In short, the tools do not see the MIG generated UCF file. This issue can be solved by following the flow found here. The digilent support thread associated with this issue is here.

This component implements a simple asynchronous SRAM interface to DDR2 converter for the Digilent Nexys4-DDR board. It uses the industry-standard SRAM control bus. Read operations are initiated by bringing CEN, OEN and LB/UB low while keeping WEN high. Valid data will be driven out the Data Output port after the specified access time has elapsed. Write operations occur when CEN, WEN and LB/UB are driven low while keeping OEN high.

The LB enable and UB enable signals support byte-wide (8-bit) data writes. During write operations, any disabled bytes will be masked out and not transmitted to the DDR. When both the LB and UB are enabled than word-wide (16-bit) data writes are executed.

This component is particularly useful for those who would like to port a design that targeted an earlier Nexys model and asynchronously accessed the onboard CellRAM. This component shares the same interface, and should allow the previous project to continue to work on the Nexys4-DDR. The only change that must be made is to the read cycle and write cycle wait times. They have increased to 210 and 260 ns, respectively

The converter component instantiates a LogiCORE MIG (Memory Interface Generator) that is configured with the following settings:

Parameter Value
Controller Type DDR2 SDRAM
Clock Period 3333 ps (300 MHz)
PHY to Controller Clock Ratio 2:1
Memory Type Components
Memory Part MT47H64M16HR-25E
Data Width 16
Data Mask Enabled
Ordering Strict
Input Clock Period 5000 ps (200MHz)
Burst Type Sequential
Output Drive Strength Fullstrength
Controller Chip Select Pin Enable
RTT (nominal) – ODT 50 Ohms
Memory Address Mapping Selection Bank-Row-Column
System Clock No Buffer
Reference Clock Use System Clock
System Reset Polarity Active Low
Debug Signals for Memory Controller Off
Internal Vref Enabled
IO Power Reduction On
XADC Instantiation Enabled¹
Internal Termination Impedance 50 Ohms

Table 1. MIG settings

¹If the XADC is used elsewhere in the design, this should be disabled. It is disabled in the Ram2Ddr version of this core

This project contains two different components: Ram2Ddr and Ram2DdrXadx. If your design does not use the XADC core anywhere else, you should use the Ram2DdrXadc component. It automatically instantiates the XADC internally to monitor the chip temperature. If your design does use the XADC core, you should use the Ram2Ddr component. You will then have to connect the device_temp line of the Ram2Ddr component to the XADC component, as described on page 122 in version 1.9 of Xilinx's 7 Series FPGAs Memory Interface Solutions Guide (UG586).

Components can either be inserted into a project as a pre-compiled netlist (.ngc), or as sources by copying the VHDL and MIG project files into your project. Both are included with the download.

Port Descriptions

Figure 1 shows the ram2ddr component block diagram with its ports:

Figure 1. Block Diagram

Port Direction Description
clk_200MHz Input Single-ended, buffered 200 MHz clock input
rst Input Active-high global reset
device_temp Input This port is active only in the ram2ddr.ngc file (where the XADC module is not internally instantiated) and shall be tied to GND in the ram2ddrxadc.ngc component. See “Xilinx UG586 7 Series FPGAs Memory Interface Solutions” for more details on driving this port.
RAM
ram_a (26:0) Input Input address
ram_dq_i (15:0) Input Data input
ram_dq_o (15:0) Output Data output
ram_cen Input Active-low Chip Enable
ram_oen Input Active-low Output Enable
ram_wen Input Active-low Write Enable
ram_ub Input Active-low Upper Byte select
ram_lb Input Active-low Lower Byte select
DDR
ddr2_addr (12:0) Output Memory Address output
ddr2_ba (2:0) Output Bank Address
ddr2_ras_n Output Active-low Row Address Strobe
ddr2_cas_n Output Active-low Column Address Strobe
ddr2_we_n Output Active-low Write Enable
ddr2_ck_p, ddr2_ck_n Output Differential Memory Clock output
ddr2_cke Output Active-high Memory Clock Enable
ddr2_cs_n Output Active-low Chip Select
ddr2_dm (1:0) Output Output Data Mask
ddr2_odt Output On-Die Termination
ddr2_dq (15:0) Bidirectional Data input/output bus
ddr2_dqs_p (1:0), ddr2_dqs_n (1:0) Bidirectional

Table 2. Port Descriptions

Bus Timing

Figure 2. Read Operation

Figure 3. Write Operation

Parameter Symbol Min Max Unit
Read cycle time tRC 210 - ns
Write cycle time tWR 260 - ns

Usage with Other Boards

In order to use this reference component with boards other than the Digilent Nexys4-DDR, the following should be modified:

  • Memory Interface Generator must be rerun and the following must be changed:
    • Controller Type and/or Memory Part (depending on the memory)
    • Controller Chip Select Pin (depending on the board)
    • RTT (nominal) – On Die Termination (depending on the board)
    • Internal Vref (depending on the board)
    • Internal Termination Impedance (depending on the board).
    • Pin constraints must be changed to match how the DDR2 is connected on the new board
  • Update the instantiation of the MIG component according to the new settings