ZedBoard OLED Demo
This project is a Vivado demo using the Zedboard's LEDs, pushbuttons and OLED Display written in Verilog. When programmed onto the board, the display will automatically be initialized. When you are done operating the demo, and want to turn your board off, press the CPU Reset Button to turn the display off. LED0 is tied to the status of the OLED display. If the LED0 is on so is the OLED display. The display can be turned on from an off state by pressing the CPU Reset Button again. The OLED Display is controlled by the BTNR, BTNU, BTNC and BTND of the D-Pad Buttons.
Additional information on how this demo can be used can be found in appropriate READMEs, linked below.
- ZedBoard with a MicroUSB Programming Cable and an external 12V Power Supply
- Vivado installation compatible with the latest release of this demo (2020.1)
- See Installing Vivado, Vitis, and Digilent Board Files for installation instructions.
Download and Usage Instructions
The following releases of this demo can be used with instructions found in the corresponding READMEs in order to run the demo.
Releases are only compatible with the version of the Xilinx tools specified in the release version number. In addition, releases are only compatible with the specified variant of the board. For example, the v2020.1-1 release for ZedBoard can only be used with Vivado 2020.1.
The latest release version for this demo is highlighted in green.
Note: Releases for FPGA demos from before 2020.1 used a different git structure, and used a different release tag naming scheme.
|Board Variant||Release Tag||Release Downloads||Setup Instructions|
|ZedBoard||OLED/2020.1-1||Release ZIP Downloads||See Using the Latest Release, below|
|ZedBoard||v2018.2-1||Release ZIP downloads||Github README|
Note for Advanced Users: All demos for the ZedBoard are provided through the ZedBoard repository on Github. Further documentation on the structure of this repository can be found on this wiki's Digilent FPGA Demo Git Repositories page.
Instructions on the use of the latest release can be found in this dropdown:
- Using the Latest Release
Note: This workflow is common across many Digilent FPGA demos. Screenshots may not match the demo you are working with.
Important: These steps are only to be used with releases for Xilinx tools versions 2020.1 and newer. Older releases may require other flows, as noted in the table of releases.
First, download and extract the '*.xpr.zip' file from the demo release page, linked above.
- Open a Vivado Project from a Release
Select the dropdown corresponding to your operating system, below.
- Build a Vivado Project
Generate a Bitstream
In order to create a file that can be used to program the target board, each stage of the “compilation pipeline” needs to be run.
This starts with Synthesis. Synthesis creates a description of the logic gates and connections between them required to perform the functionality described by the HDL files, given the constraints included in XDC files. To run Synthesis click either in the toolbar or in the Flow Navigator. The output of Synthesis is then passed to Implementation.
Implementation has several steps. The steps that are always run are Opt Design (Optimize the design to fit on the target FPGA), Place Design (Lay out the design in the target FPGA fabric), and Route Design (Route signals through the fabric). To run Implementation click either in the toolbar or in the Flow Navigator. This output is then passed on to the Bitstream Generator.
The Bitstream Generator generates the final output file needed for programming the FPGA. To run Bitstream Generation click either in the toolbar or in the Flow Navigator. With no settings changed, the generator will create a '.bit' file.
Depending on the complexity of the design, the board used, and the strength of your computer, the process of building the project can take between 5 and 60 minutes. When complete, a pop up dialog will appear, prompting you to select one of several options. None are relevant for the purposes of this guide, so click Cancel. The “write_bitstream complete” status message can be seen in the top right corner of the window, indicating that the demo is ready to be deployed to your board.
- Set up the ZedBoard
Plug the microUSB programming cable into the ZedBoard's JTAG port and the 12V Power Supply into the Barrel Jack next to the JTAG port.
- Program a Bitstream onto an FPGA Board
Vivado's Hardware Manager can be opened by clicking on Open Hardware Manager at the bottom of the Flow Navigator pane on the left side of the Vivado window.
The first step to programming a device is to connect the Vivado Hardware Server to it as a target. To get to the Open Hardware Target wizard click the link in the green banner near the top of the window. From the drop-down that opens, select .
Once the wizard opens, click Next.
The next screen asks if the hardware server is local or remote. If the board is connected to the host computer choose local, if it is connected to another machine choose remote and fill in the Host Name and Port fields.
Click Next to continue.
This screen gives a list of devices connected to the hardware server. If there is only one connected it will be the only device shown.
Click Next to continue.
The final screen shows a summary of the options selected in the wizard. Verify the information and click Finish. The board is now connected to the hardware server.
To program the device with the bit file generated earlier, either click the link in the green banner at the top of the window or click the button in the Flow Navigator under . From the drop-down that opens, select the device to program (Example: ) and the following window will open:
The Bitstream File field should be automatically filled in with the bit file generated earlier. If not, click the button at the right end of the field and navigate to
<Project Directory>/<Project Name>.runs/impl_1/ and select the bit file (Example: ). Now click Program. This will connect to the board, clear the current configuration, and program it using the new bit file.
1. Startup and Bringdown
The OLED display can be turned on and off by pressing the right D-Pad Button (BTNR). When the board is first programmed, the display will automatically be initialized. When you are done operating the demo, and want to turn your board off, press the CPU Reset Button to turn the display off. The status of the display is indicated by LED0, if it is on, the display is on. The display can be turned on from an off state by pressing the CPU Reset Button again.
Make sure to turn off the OLED display before shutting down or reprogramming your board.
2. Toggle the Display
3. Display Strings
All materials related to the use of the ZedBoard can be found on its Resource Center.
For a walkthrough of the process of creating a simple baremetal software project in Vivado and Vitis, see Getting Started with Vivado IP Integrator and Vitis. Information on important parts of the GUIs, and indirect discussion of the steps required to modify, rebuild, and run this demo in hardware can also be found here.
For technical support, please visit the FPGA section of the Digilent Forum.