Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| reference:instrumentation:zmoddac:reference-manual [2019/11/04 07:36] – [2.4. AWG Out] Mircea Dabacan | reference:instrumentation:zmoddac:reference-manual [2019/11/11 20:29] (current) – removed Arthur Brown | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Zmod DAC Reference Manual ====== | ||
| - | The Digilent Zmod DAC, is an open-source hardware SYZYGY™ ((The “SYZYGY™ ” mark is owned by Opal Kelly.)) compatible pod containing a dual-channel DAC and the associated front end. The Zmod DAC is intended to be used with any SYZYGY™ compatible carrier board having the required capabilities. | ||
| - | |||
| - | {{Digilent Image Gallery | ||
| - | | image = {{reference/ | ||
| - | | image = {{reference/ | ||
| - | }}// | ||
| - | |||
| - | The analog outputs can be connected to a circuit using SMA cables. Driven by the SYZYGY™ carrier, the Zmod DAC can generate two simultaneous signals | ||
| - | |||
| - | The Zmod DAC was designed to be a piece in a modular, HW and SW open-source ecosystem. Combined with a SYZYGY™ carrier, other SYZYGY™ compatible pods, Zmod DAC can be used for a variety of applications: | ||
| - | |||
| - | This document describes the Zmod DAC's circuits, with the intent of providing a better understanding of its electrical functions, operations, and a more detailed description of the hardware’s features and limitations. It is not intended to provide enough information to enable complete duplication of the Zmod DAC, but can help users to design custom configurations for programmable parts in the design. | ||
| - | |||
| - | ===== Features ===== | ||
| - | |||
| - | * Channels: 2 | ||
| - | * Channel type: single ended | ||
| - | * Resolution: | ||
| - | * Absolute Resolution (amplitude ≤1.25V): | ||
| - | * Absolute Resolution (amplitude > | ||
| - | * Accuracy - typical (|Vout| ≤ 1.25V): ±10mV ± 0.5% FIXME | ||
| - | * Accuracy - typical (|Vout| > 1.25V): ±25mV ± 0.5% FIXME | ||
| - | * Output impedance: 50Ω | ||
| - | * Sample rate (real time): 100MS/s. | ||
| - | * AC amplitude (max): ±5 V. | ||
| - | * Analog bandwidth: 40 MHz @ 3dB, 20 MHz @ 0.5dB, 14 MHz @ 0.1dB | ||
| - | * Slew rate (2V step): 180V/μs | ||
| - | |||
| - | |||
| - | |||
| - | ===== 1. Architectural Overview and Block Diagram ===== | ||
| - | Zmod ADC's high-level block diagram is presented in [[reference: | ||
| - | |||
| - | |||
| - | The **Analog Output** block is also called the **AWG** (Arbitrary Waveform Generator), because of similar structure and behavior to such a front end. The signals in this circuitry use “AWG” indexes, to indicate they are related to the AWG block. Signal and equations also use certain naming conventions. Analog voltages are prefixed with a " | ||
| - | |||
| - | * The **Arbitrary Outputs/ | ||
| - | * **DAC**: the digital-to-analog converter for both AWG channels | ||
| - | * **AWG ref**: refernce voltage for the DAC | ||
| - | * **I/V**: current to bipolar voltage converters | ||
| - | * **Out**: output stages | ||
| - | * **Protection**: | ||
| - | * The **Power Supplies and Control** block generates all internal supply voltages. | ||
| - | * The **MCU** works as a I2C memory for two different purposes: | ||
| - | * The **DNA** includes the standard [[https:// | ||
| - | * The **Calibration Memory** stores all calibration parameters. The Zmod DAC includes no analog calibration circuitry. Instead, a calibration operation is performed at manufacturing (or by the user), and parameters are stored in memory. The application software uses these parameters to correct the generated signals | ||
| - | |||
| - | In the sections that follow, schematics are not shown separately for identical blocks. | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | ---- | ||
| - | ===== 2. Arbitrary Waveform Generator ===== | ||
| - | |||
| - | ==== 2.1. AWG Reference ==== | ||
| - | |||
| - | |||
| - | As shown in [[reference: | ||
| - | |||
| - | * Initial accuracy: ±0.1% (maximum) | ||
| - | * Maximum temperature coefficient: | ||
| - | * Operating temperature range: −40°C to +125°C | ||
| - | * Output current: +10 mA source/−3 mA sink | ||
| - | * Low quiescent current: 100 μA (maximum) | ||
| - | * Low dropout voltage: 250 mV at 2 mA | ||
| - | * Output noise (0.1 Hz to 10 Hz): <10 μV p-p at 1.2 V (typical) | ||
| - | |||
| - | A divided version is provided to the DAC: | ||
| - | |||
| - | $$V_{REFIO\_AWG}=V_{REF1V2\_AWG} \cdot \frac{R_{27}}{R_{26}+{R_{27}}}=1V\label{1}\tag{1}$$ | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | ---- | ||
| - | |||
| - | ==== 2.2. AWG DAC ==== | ||
| - | |||
| - | The Analog Devices [[http:// | ||
| - | * Power dissipation @ 3.3V, 2 mA output: 86 mW @ 125MS/s, sleep mode: <3 mW @ 3.3V | ||
| - | * Supply voltage: 1.8V to 3.3V | ||
| - | * SFDR to Nyquist: 84 dBc @ 1 MHz output, 75 dBc @ 10 MHz output | ||
| - | * AD9717 NSD @ 1 MHz output, 125MS/s, 2 mA: −151 dBc/ | ||
| - | * Differential current outputs: 1 mA to 4 mA | ||
| - | * CMOS inputs with single-port operation | ||
| - | * Output common mode: 0 to 1.2 V | ||
| - | * Small footprint, 40-lead LFCSP RoHS-compliant package | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | The parallel Data Bus, the single ended 100 MHz clock and the SPI configuration bus are driven by the SYZYGY™ carrier board FPGA. | ||
| - | External V< | ||
| - | The Full Scale is set via the FSADJx pins. The [[http:// | ||
| - | |||
| - | The Full Scale DAC output current is: | ||
| - | |||
| - | $$I_{outAWGFS}=32 \cdot \frac{V_{REFIO\_AWG}}{R_{set}}\label{2}\tag{2}$$ | ||
| - | |||
| - | For high-gain: | ||
| - | |||
| - | $$I_{outAWGFS\_HG}=32 \cdot \frac{1V}{8.06k \Omega}=3.97mA\label{3}\tag{3}$$ | ||
| - | |||
| - | For low-gain: | ||
| - | |||
| - | $$I_{outAWGFS\_HG}=32 \cdot \frac{1V}{32k \Omega}=1mA\label{4}\tag{4}$$ | ||
| - | |||
| - | The [[http:// | ||
| - | * −3 dB bandwidth, 150 MHz | ||
| - | * Single-supply 1.8V to 5.5V operation | ||
| - | * Low on resistance: 2.5 Ω typical | ||
| - | |||
| - | |||
| - | ==== 2.3. AWG I/V ==== | ||
| - | |||
| - | IC5B in [[reference: | ||
| - | |||
| - | Important [[http:// | ||
| - | * Low cost | ||
| - | * 325 MHz, −3 dB bandwidth (G = +1) | ||
| - | * 1000 V/μs slew rate | ||
| - | * Gain flatness: 0.1 dB to 28 MHz | ||
| - | * Low noise: 7 nV/√Hz | ||
| - | * Low power: 5.4 mA/ | ||
| - | * Low distortion: −85 dBc@5MHz, RL=1kΩ | ||
| - | * Wide supply range from 3 V to 12 V | ||
| - | * Small packaging | ||
| - | |||
| - | $$V_{OUT\; | ||
| - | $$=( 1-2 \cdot \{ A_U \} ) \cdot I_{outAWGFS} \cdot R_{44}=\{ A_B \} \cdot I_{outAWGFS} \cdot R_{44}\label{5}\tag{5}$$ | ||
| - | |||
| - | |||
| - | Where: | ||
| - | |||
| - | $$n = 14; - \; | ||
| - | $$D \in \left[ {\left. {0 \ldots {2^{n}}} \right)} \right. = \left[ {0 \ldots {2^{n}} - 1} \right];\; - \; | ||
| - | $$\left\{ {{A_U}} \right\} = \frac{D}{{{2^n}}} \in \left[ {\left. {0 \ldots 1} \right)} \right.;\; - \; | ||
| - | $$\left\{ {{A_B}} \right\} = \left( {1 - 2 \cdot \left\{ {{A_U}} \right\}} \right) \in \left[ {\left. { - 1 \ldots 1} \right)} \right.;\; - \; | ||
| - | |||
| - | |||
| - | |||
| - | The IC5B output voltage range extends between: | ||
| - | |||
| - | $$ - V_{OUT\; | ||
| - | |||
| - | Where (for high gain, respectively, | ||
| - | |||
| - | $$V_{OUT\; | ||
| - | $$V_{OUT\; | ||
| - | |||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | |||
| - | {{: | ||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | // | ||
| - | ---- | ||
| - | |||
| - | ==== 2.4. AWG Out ==== | ||
| - | |||
| - | IC8 in [[reference: | ||
| - | |||
| - | * Low noise: 2.1 nV/√Hz input voltage noise; 2.1 pA/√Hz input current noise | ||
| - | * Custom compensation | ||
| - | * Constant bandwidth from G = −1 to G = −10 | ||
| - | * High speed: 200 MHz (G = −1), 190 MHz (G = −10) | ||
| - | * Low power: 34 mW or 6.7 mA typical for 5 V supply | ||
| - | * Output disable feature, 1.3 mA | ||
| - | * Low distortion: −93 dBc second harmonic, fC = 1 MHz; −108 dBc third harmonic, fC = 1 MHz | ||
| - | * DC precision: 1 mV maximum input offset voltage; 0.5 μV/°C input offset voltage drift | ||
| - | * Wide supply range, 5 V to 24 V | ||
| - | * Low price | ||
| - | * Small packaging: Available in SOIC-8 and MSOP-8 | ||
| - | |||
| - | |||
| - | $$V_{AWG\; | ||
| - | |||
| - | The output voltage range depends on High-gain versus Low-gain selection: | ||
| - | |||
| - | $$ - 5.49V < - 5V < V_{AWG\; | ||
| - | $$ - 1.37V < 1.25V < V_{AWG\; | ||
| - | |||
| - | |||
| - | Low-gain is used to generate low amplitude signals with improved accuracy. Any amplitude of the output signal can be generated by combining LowGain/ | ||
| - | |||
| - | With the 14-bit DAC, the absolute resolution of the AWG AC component is: | ||
| - | |||
| - | $$at\; | ||
| - | $$at\; | ||
| - | |||
| - | AD8021 is supplied with +8.5V/-8V (the VCC8V0 voltage is in fact 8.5V). Conform to the data sheet, the worst case output voltage swing is V< | ||
| - | |||
| - | The nominal resistance of the PTC in the feedback loop is 33 ohm. The maximum current delivered by te AWG is 30mA. | ||
| - | |||
| - | To avoid saturation, the voltage in \ref{9} should stay in: | ||
| - | |||
| - | $$ -8V + 1.8V + 33\Omega *30mA = -5.21V < -5V < V_{AWG\; | ||
| - | |||
| - | Only inner (tighter) ranges are used in equations \ref{10} and \ref{12}, for providing tolerance margins. | ||
| - | |||
| - | To generate a particular voltage value at the output of the AWG channel, the user application sends a signed 14 bit integer to the DAC. This value is computed as: | ||
| - | $${N} = \frac{(V_{Out}-CA)}{(1+CG) \cdot (Range)}* 2^{13}\in (-2^{13}, +2^{13}) \label{13}\tag{13}$$ | ||
| - | |||
| - | were: | ||
| - | |||
| - | * Vout = the desired output voltage. Could be separated in: | ||
| - | * Voffset= the DC component voltage | ||
| - | * Vamplitude= the AC instantaneous voltage | ||
| - | * CA = calibration additive constant (for the appropriate channel and gain; see [[reference: | ||
| - | * CG = calibration Gain constant (for the appropriate channel and gain; see [[reference: | ||
| - | * Range = the ideal AWG output stage range (approximation of the values in equation \ref{10}): | ||
| - | * 1 * 1.33 = 1.33 (for LG: +/-1.25V) or | ||
| - | * 4 * 1.33 = 5.32 (for HG: +/-5V) | ||
| - | |||
| - | The R146 PTC thermistor provides thermal protection in case of an output short-circuit. | ||
| - | |||
| - | The IC7 relay (non-latching) is OPEN at the power-on, decoupling the power-on glitch of the OpAmp from the load. It is CLOSED by the FPGA, via Q1. | ||
| - | R37 is a pull down when IC7 is OPEN and a dummy load when IC7 is CLOSED. | ||
| - | D2 is an ESD suppressor. | ||
| - | |||
| - | R36 is the 50Ω AWG output impedance. | ||
| - | ---- | ||
| - | ==== 2.3. AWG output stage protection ==== | ||
| - | |||
| - | Important [[https:// | ||
| - | * Single-supply operation: 4.5 V to 16 V | ||
| - | * Input capability beyond the rails | ||
| - | * Rail-to-rail output swing | ||
| - | * Continuous output current: 35 mA | ||
| - | * Peak output current: 250 mA | ||
| - | * Offset voltage: 10 mV | ||
| - | * Slew rate: 6 V/μs | ||
| - | * Unity gain stable with large capacitive loads | ||
| - | * Supply current: 700 μA per amplifier | ||
| - | * Qualified for automotive applications Low cost | ||
| - | |||
| - | The protection circuit in [[reference: | ||
| - | |||
| - | $$\frac {AVCC8V0 \cdot R_{77}}{R_{72}+R_{77}} = \frac{(AVCC8V0 - R_{70} \cdot I_{out}) \cdot R_{74}+ | ||
| - | AVCC8V0AWG1 \cdot R_{73}}{R_{73}+R_{74}}$$ | ||
| - | |||
| - | $$ I_{out}=0.0411 \cdot \frac{AVCC8V0}{10\Omega} +0 .012 \cdot \frac{AVCC8V0AWG1}{10\Omega} \label{14}\tag{14}$$ | ||
| - | |||
| - | The corner current (when V< | ||
| - | $$ I_{outC}=42mA \label{15}\tag{15}$$ | ||
| - | |||
| - | The short-to-GND current (when AVCC8V0AWG1 is forced to 0V) is: | ||
| - | $$ I_{outSGND}=33mA \label{16}\tag{16}$$ | ||
| - | |||
| - | The current (when AVCC8V0AWG1 is forced to -15V) is: | ||
| - | $$ I_{outS-15}=14mA \label{17}\tag{17}$$ | ||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | // | ||
| - | ---- | ||
| - | |||
| - | |||
| - | ==== 2.5. AWG Spectral Characteristics ==== | ||
| - | |||
| - | For low frequency range, the spectral characteristic was traced by a network analyzer function, with the ZmodDAC connected to a ZmodADC, as shown in [[reference: | ||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | // | ||
| - | |||
| - | However, the figure [[reference: | ||
| - | |||
| - | To trace the analog bandwidth of the DAC and output stage beyond the theoretical limit of f< | ||
| - | * The AWG was set to generate a 2MHz rectangular signal, 100mV amplitude; | ||
| - | * the theoretical amplitudes of the fundamental and first 69 harmonics was computed; | ||
| - | * the actual amplitudes of the fundamental and first 69 harmonics were measured with a high sampling rate scope (10GSPS, 2GHz BW); | ||
| - | * the dB difference between the theoretical and measured amplitudes was plotted. This represents an approximation of the frequency characteristic of the DAC and output stage. | ||
| - | |||
| - | The characteristic is shown in [[reference: | ||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | // | ||
| - | |||
| - | The 3dB bandwidth is 40MHz+, the 0.5dB bandwidth is 20MHz+, the ±0.1dB flatness band is 14MHz+. | ||
| - | |||
| - | The 3dB bandwidth is close to the theoretical Nyquist limit for a 100MHz sampling system. This has the advantage of very sharp edges (see the rectangular signal in [[reference: | ||
| - | the right side of [[reference: | ||
| - | |||
| - | The typical Slew Rate of the AWG can be read in [[reference: | ||
| - | |||
| - | $$ SR=\frac{2.05V}{11.2ns}=183V/ | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | // | ||
| - | |||
| - | {{: | ||
| - | {{: | ||
| - | // | ||
| - | |||
| - | |||
| - | ---- | ||
| - | |||
| - | ===== 3. MCU ===== | ||
| - | |||
| - | The [[https:// | ||
| - | |||
| - | The DNA and the Factory Calibration Coefficients are stored in the Flash memory of the MCU, which appears to the I2C interface as " | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | * Program Memory Type: Flash | ||
| - | * Program Memory Size (KB): 4 | ||
| - | * CPU Speed (MIPS/ | ||
| - | * SRAM Bytes: 256 | ||
| - | * Data EEPROM/HEF (bytes): 256 | ||
| - | * Digital Communication Peripherals: | ||
| - | * Capture/ | ||
| - | * Timers: 1 x 8-bit, 1 x 16-bit | ||
| - | * Number of Comparators: | ||
| - | * Temperature Range (C): -40 to 85 | ||
| - | * Operating Voltage Range (V): 1.8 to 5.5 | ||
| - | * Pin Count: 14 | ||
| - | * Low Power: Yes | ||
| - | |||
| - | // | ||
| - | ^ Address | ||
| - | | 0x8000 - 0x80FF | ||
| - | | 0x8100 - 0x817F | ||
| - | | 0x8180 - 0x83FF | ||
| - | ==== 3.1. SYZYGY™ | ||
| - | |||
| - | The Zmod DAC is compliant with [[https:// | ||
| - | |||
| - | // | ||
| - | ^ Contents | ||
| - | |DNA full data length | ||
| - | |DNA header length | ||
| - | |SYZYGY DNA major version | ||
| - | |SYZYGY DNA minor version | ||
| - | |Required SYZYGY DNA major version | ||
| - | |Required SYZYGY DNA minor version | ||
| - | |Maximum operating 5V load (mA) |uint16 |2 |600 |0x8008 | ||
| - | |Maximum operating 3.3V load (mA) |uint16 |2 |1 |0x800A | ||
| - | |Maximum VIO load (mA) | ||
| - | |Attribute flags | ||
| - | |Minimum operating VIO1 (10 mV steps)|uint16 |2 |180 |0x8010 | ||
| - | |Maximum operating VIO1 (10 mV steps)|uint16 |2 |180 |0x8012 | ||
| - | |Minimum operating VIO2 (10 mV steps)|uint16 |2 |170 |0x8014 | ||
| - | |Maximum operating VIO2 (10 mV steps)|uint16 |2 |190 |0x8016 | ||
| - | |Minimum operating VIO3 (10 mV steps)|uint16 |2 |0 |0x8018 | ||
| - | |Maximum operating VIO3 (10 mV steps)|uint16 |2 |0 |0x801A | ||
| - | |Minimum operating VIO4 (10 mV steps)|uint16 |2 |0 |0x801C | ||
| - | |Maximum operating VIO4 (10 mV steps)|uint16 |2 |0 |0x801E | ||
| - | |Manufacturer name length | ||
| - | |Product name length | ||
| - | |Product model / Part number length | ||
| - | |Product version / revision length | ||
| - | |Serial number length | ||
| - | |RESERVED | ||
| - | |CRC-16 (most significant byte) |uint8 | ||
| - | |CRC-16 (least significant byte) | ||
| - | | END DATA HEADER | ||
| - | |Manufacturer name | ||
| - | |Product name |string |13 |Zmod DAC 1411|0x8034 | ||
| - | |Product model / Part number | ||
| - | |Product version / revision | ||
| - | |Serial number | ||
| - | |||
| - | ==== 3.2. Calibration Memory ==== | ||
| - | |||
| - | The analog circuitry described in previous chapters includes passive and active electronic components. The datasheet specs show parameters (resistance, | ||
| - | |||
| - | * 0.1% resistors and 1% capacitors in all the critical analog signal paths | ||
| - | * Capacitive trimmers for balancing the Scope Input Divider and Gain Selection | ||
| - | * No other mechanical trimmers (as these are big, expensive, unreliable and affected by vibrations, aging, and temperature drifts) | ||
| - | * Software calibration, | ||
| - | * User software calibration, | ||
| - | |||
| - | A software calibration is performed on each device as a part of the manufacturing test. The AWG outputs are connected to calibrated voltmeters. A set of measurements is used to identify all the DC errors (Gain, Offset) of each analog stage. Correction (Calibration) parameters are computed and stored in the Calibration Memory, on the Zmod DAC device, both as Factory Calibration Data and User Calibration Data. The WaveForms software allows the user performing an in-house calibration and overwrite the User Calibration Data. Returning to Factory Calibration is always possible. | ||
| - | |||
| - | The Software reads the calibration parameters from the Zmod DAC MCU via the I2C bus and uses them to correct the generated signals. The structure of the data is shown below: | ||
| - | |||
| - | // | ||
| - | ^ Heading 1 | **Name** | ||
| - | | Magic ID | ||
| - | | Calibration Time | ||
| - | | Channel 1 LG Gain | CG | 4 | ||
| - | | Channel 1 LG Offset | ||
| - | | Channel 1 HG Gain | CG | 4 | ||
| - | | Channel 1 HG Offset | ||
| - | | Channel 2 LG Gain | CG | 4 | ||
| - | | Channel 2 LG Offset | ||
| - | | Channel 2 HG Gain | CG | 4 | ||
| - | | Channel 2 HG Offset | ||
| - | | Channel 1 Linearity | ||
| - | | Channel 2 Linearity | ||
| - | | Log | | ||
| - | | CRC | | ||
| - | |||
| - | |||
| - | // | ||
| - | ^ | ||
| - | | 0x7000 - 0x707F | ||
| - | | 0x7080 - 0x70FF | ||
| - | |||
| - | At the power up the EEPROM memory is protected against write operations. To disable the write protection one has to write a magic number to a magic address over I2C. To re-enable the write protection one has to write a any other number to the magic address. | ||
| - | |||
| - | // | ||
| - | ^ Magic Number | ||
| - | | 0xD2 | ||
| - | |||
| - | ---- | ||
| - | ===== 4. Power Supplies ===== | ||
| - | |||
| - | This block includes the internal power supplies. | ||
| - | |||
| - | The Zmod DAC gets the digital rails from the carrier board, via the SYZYGY™ connector: | ||
| - | |||
| - | * VCC5V0 - used for relays and analog supplies | ||
| - | * VCC3V3 - used for the MCU and analog supplies | ||
| - | * Vadj = 1.8V - used for the DAC digital rail | ||
| - | |||
| - | |||
| - | The internal analog rails sequence is: | ||
| - | |||
| - | * AVCC3V3 - DAC analog rail, I/V converter (after VCC5V0) | ||
| - | * AVCC-2V5 - I/V converter (after VCC5V0) | ||
| - | * AVCC-8V0, AVCC8V0 - AWG output stage (after VCC3V3) | ||
| - | |||
| - | ==== 4.1. AVCC3V3 ==== | ||
| - | |||
| - | The analog supply AVCC3V3 is built from VCC5V0 using IC10, an [[https:// | ||
| - | * Input voltage supply range: 2.3 V to 5.5 V | ||
| - | * 300 mA maximum output current | ||
| - | * Fixed and adjustable output voltage versions | ||
| - | * Very low dropout voltage: 85 mV at 300 mA load | ||
| - | * Low quiescent current: 45 µA at no load | ||
| - | * Low shutdown current: <1 µA | ||
| - | * Initial accuracy: ±1% accuracy | ||
| - | * Up to 31 fixed-output voltage options available from 1.75 V to 3.3 V | ||
| - | * Adjustable-output voltage range 0.8 V to 5.0 V (ADP123) | ||
| - | * Excellent PSRR performance: | ||
| - | * Excellent load/line transient response | ||
| - | * Optimized for small 1.0 μF ceramic capacitors | ||
| - | * Current limit and thermal overload protection | ||
| - | * Logic controlled enable | ||
| - | * Compact packages: 5-lead TSOT and 6-lead 2 mm × 2 mm LFCSP | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | ==== 4.2. AVCC-2V5 ==== | ||
| - | |||
| - | The AVCC-2V5 analog power supply is implemented with the [[http:// | ||
| - | |||
| - | * 1.2 A maximum load current | ||
| - | * ±2% output accuracy over temperature range | ||
| - | * 1.4 MHz switching frequency | ||
| - | * High efficiency up to 91% | ||
| - | * Current-mode control architecture | ||
| - | * Output voltage from 0.8 V to 0.85 × VIN | ||
| - | * Automatic PFM/PWM mode switching | ||
| - | * Integrated high-side MOSFET | ||
| - | * Internal compensation and soft start | ||
| - | * Undervoltage lockout (UVLO), Overcurrent protection (OCP) and thermal shutdown (TSD) | ||
| - | * Available in ultrasmall, 6-lead TSOT package | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | The output voltage is: | ||
| - | |||
| - | $$V_{OUT}=-V_{FB} \cdot \frac{R_{49}+R_{50}}{R_{50}}=-2.5V\label{19}\tag{19}$$ | ||
| - | |||
| - | Where: | ||
| - | |||
| - | $${V_{FB}} = 0.8V\; | ||
| - | |||
| - | ==== 4.3. AVCC8V0 ==== | ||
| - | |||
| - | The user power supplies [[reference: | ||
| - | |||
| - | * 1.4A current limit | ||
| - | * Minimum input voltage 1.8V | ||
| - | * Pin-selectable 650 kHz or 1.3 MHz PWM frequency | ||
| - | * Adjustable output voltage up to 20 V | ||
| - | * Adjustable soft start | ||
| - | * Undervoltage lockout | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | The output voltage is: | ||
| - | |||
| - | $$V_{OUT}=V_{FB} \cdot \frac{R_{80}+R_{84}}{R_{84}}=8.538V\label{21}\tag{21}$$ | ||
| - | |||
| - | Where: | ||
| - | |||
| - | $${V_{FB}} = 1.235V\; | ||
| - | |||
| - | The supply is enabled after VCC5V0 and AVCC3V3 (see EN_AVCC in [[reference: | ||
| - | |||
| - | ---- | ||
| - | ==== 4.4. AVCC-8V0 ==== | ||
| - | |||
| - | The user power supplies [[reference: | ||
| - | |||
| - | IC13 introduces the required inversion for the negative supply. [[https:// | ||
| - | |||
| - | * Low power: 1.1 mA/amp | ||
| - | * Low wideband noise: 2.1 nV/√Hz, 1.4 pA/√Hz | ||
| - | * Low 1/f noise:7 nV/√Hz @ 10 Hz, 13 pA/√Hz @ 10 Hz | ||
| - | * Low distortion: −105 dBc @ 100 kHz, VO = 2 V p-p | ||
| - | * High speed: 80 MHz, −3 dB bandwidth (G = +1), 12 V/µs slew rate, 175 ns settling time to 0.1% | ||
| - | * Low offset voltage: 0.3 mV maximum | ||
| - | * Rail-to-rail output | ||
| - | * Power down | ||
| - | * Wide supply range: 2.7 V to 12 V | ||
| - | |||
| - | {{: | ||
| - | // | ||
| - | |||
| - | The output voltage is: | ||
| - | |||
| - | $$V_{AVCC8V0}=-V_{FB} \cdot \frac{R_{56}}{R_{60}}=-8.035V\label{23}\tag{23}$$ | ||
| - | |||
| - | Where: | ||
| - | |||
| - | $${V_{FB}} = 1.235V\; | ||
| - | |||
| - | The supply is enabled after VCC5V0 and AVCC3V3. | ||
| - | |||
| - | ---- | ||
| - | |||
| - | ===== 5. The SYZYGY™ Connector ===== | ||
| - | |||
| - | The SYZYGY™ connector in provides the interface with the carrier board. The used signals are: | ||
| - | * Power rails | ||
| - | * VCC5V0 | ||
| - | * VCC3V3 | ||
| - | * VADJ - needs to be set by the carier board to 1.8V | ||
| - | * GND | ||
| - | * Shield | ||
| - | * SYZYGY™ I2C bus: | ||
| - | * MCU_SCLUSCK | ||
| - | * MCU_SDA_MOSI | ||
| - | * DAC single ended input clock | ||
| - | * CLKIN_AWG (coupled with GND in the differential C2P pair) | ||
| - | * DAC single ended output clock: | ||
| - | * CLKIO_AWG (coupled with GND in the differential P2C pair) | ||
| - | * R_GA for geographical address identification | ||
| - | * Gain selector signals: | ||
| - | * SET_FS_AWG1 | ||
| - | * SET_FS_AWG2 | ||
| - | * DAC data bus: DIN_AWG_0...13 | ||
| - | * ADC SPI bus: | ||
| - | * CS_SC1n | ||
| - | * SCLK_SC | ||
| - | * SDIO_SC | ||
| - | * relay control | ||
| - | * RL_EN_AWG - enables the AWG outputs | ||
| - | * RESET_AWG | ||
| - | {{: | ||
| - | // | ||
| - | |||
| - | ===== 6. The SYZYGY™ compatibility table ===== | ||
| - | |||
| - | // | ||
| - | ^ Parameter | ||
| - | | Maximum 5V supply current | ||
| - | | Maximum 3.3V supply current | ||
| - | | VIO supply voltage | ||
| - | | Maximum VIO supply current | ||
| - | | Total number of I/O | 21 | | ||
| - | | Number of differential I/O pairs | 0 | | ||
| - | | Width | Single | ||
| - | |||
| - | ---- | ||
| - | |||
| - | **Written by Mircea Dabacan, PhD, Technical University of Cluj-Napoca Romania** | ||