Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
learn:instrumentation:tutorials:openscope-mz:calibration [2017/06/09 16:31] – Sam Klearn:instrumentation:tutorials:openscope-mz:calibration [2021/05/14 23:08] (current) – ↷ Links adapted because of a move operation Arthur Brown
Line 12: Line 12:
  
   - Launch [[http://waveformslive.com/ | WaveForms Live]].   - Launch [[http://waveformslive.com/ | WaveForms Live]].
-  - [[/reference/software/waveforms-live/add-device | Add the OpenScope MZ]] to WaveForms Live. \\  +  - [[software:waveforms-live:add-device| Add the OpenScope MZ]] to WaveForms Live. \\  
-  - Click the **More** button on the device card and select **Configure**. \\ \\ {{ :reference:instrumentation:openscope-mz:waveforms-live-openscope-calibration-4.png |}} \\ \\ {{ :reference:instrumentation:openscope-mz:waveforms-live-openscope-calibration-5.png |}} \\ \\ +  - Click the **More** button on the device card and select **Configure**. \\ \\ {{ reference:test-and-measurement:openscope-mz:waveforms-live-openscope-calibration-4.png |}} \\ \\ {{ reference:test-and-measurement:openscope-mz:waveforms-live-openscope-calibration-5.png |}} \\ \\ 
-  - Under the **Calibration** section click **Calibrate**. \\ \\ {{ :reference:instrumentation:openscope-mz:waveforms-live-openscope-calibration-6.png |}} \\ \\ +  - Under the **Calibration** section click **Calibrate**. \\ \\ {{ reference:test-and-measurement:openscope-mz:waveforms-live-openscope-calibration-6.png |}} \\ \\ 
   - Device specific instructions are provided.    - Device specific instructions are provided. 
     - Connect the solid red wire to the solid orange wire.     - Connect the solid red wire to the solid orange wire.
     - Connect the solid white wire to the solid blue wire.     - Connect the solid white wire to the solid blue wire.
-    - Click **Next** to begin calibration.  \\ \\ {{ :reference:instrumentation:openscope-mz:waveforms-live-openscope-calibration-7.png |}} \\ \\  +    - Click **Next** to begin calibration.  \\ \\ {{ reference:test-and-measurement:openscope-mz:waveforms-live-openscope-calibration-7.png |}} \\ \\  
-  - The calibration process takes about 30 seconds.  \\ \\ {{ :reference:instrumentation:openscope-mz:waveforms-live-openscope-calibration-8.png |}} \\ \\  +  - The calibration process takes about 30 seconds.  \\ \\ {{ reference:test-and-measurement:openscope-mz:waveforms-live-openscope-calibration-8.png |}} \\ \\  
-  - The calibration information is displayed.  Select the desired **storage location** (flash is recommended) and click **Save**.  Then click **Done**.  \\ \\ {{ :reference:instrumentation:openscope-mz:waveforms-live-openscope-calibration-9.png |}} \\ \\ +  - The calibration information is displayed.  Select the desired **storage location** (flash is recommended) and click **Save**.  Then click **Done**.  \\ \\ {{ reference:test-and-measurement:openscope-mz:waveforms-live-openscope-calibration-9.png |}} \\ \\ 
   - The new calibration data has been applied to the instrument and will be applied at boot.   - The new calibration data has been applied to the instrument and will be applied at boot.