Using the Waveform Generator

Introduction

This guide explains the use of the Wavegen instrument in WaveForms. This instrument is used to apply signals to a Digilent Test & Measurement Device's analog output channels.


Prerequisites

  • A Digilent Test & Measurement Device with Analog Input/Output Channels
  • A Computer with WaveForms Software Installed

1. Opening the WaveGen

1.1

Plug in the Test & Measurement Device, then start WaveForms and make sure the device is connected.

If no device is connected to the host computer when WaveForms launches, the Device Manager will be launched. Make sure that the device is plugged in and turned on, at which point it will appear in the Device Manager's device list (1). Click on the device in the list to select it, then click the Select button (2) to close the Device Manager.

Note: “DEMO” devices are also listed, which allow the user to use WaveForms and create projects without a physical device.

Note: The Device Manager can be opened by clicking on the “Connected Device” button in the bottom right corner of the screen (3.), or by selecting “Device Manager” from the “Settings” menu at the top of the screen.


1.2

Once the Welcome page loads, in the instrument panel at the left side of the window, click on the Wavegen button to open the Waveform Generator instrument.


1.3

Once the Wavegen instrument opens, the window contains the preview plot (1.) showing what the expected waveform is, the configuration panel (2.) left of the preview, and the control toolbar (3.) above both.

2. Using the WaveGen

This section details how to configure and run the Wavegen instrument

2.1 Hardware Setup

To demonstrate the capabilities of the Waveform Generator instrument, the Scope instrument is used to visualize the Waveform Generator output signal. This step describes setting up a simple loopback circuit that connects the test & measurement device's Waveform Generator and Oscilloscope pins.

Connect the Test & Measurement device's scope channel 1 pin (orange wire) to the device's wavegen channel 1 output pin (yellow wire). For devices that use differential input channels, such as the Analog Discovery Studio with MTE cables, make sure to connect the scope channel 1 negative pin (orange wire with white stripes) to the ground pin associated with wavegen channel 1 (black wire).


2.2 Set up Oscilloscope

With the loopback circuit set up, return to WaveForm's Welcome page by clicking on the Welcome tab at the top of the screen. In the Welcome page, open the Scope instrument, then click the “Run” button () in the control bar near the top of the window to begin measuring the signal.

Next, the Wavegen and Scope instruments will be docked so that any changes to Wavegen settings can immediately be viewed in the Scope.

In order to show both the Wavegen and the Scope instruments on the screen at once, click on the Docking Windows button () in the top right corner of the screen.

Note: To return to the default tabbed view later, click on the “Tabbed Windows” button () adjacent to the Docking Windows button.


2.3 Configure Signal Type

Begin by changing the signal type. Click the Type drop-down and choose Square.


2.4

The frequency is configured by selecting the value from the Frequency drop-down list, or by clicking into the field and manually typing it in (including units and an SI suffix). Set the frequency to 200 Hz.


2.5

Configuring the amplitude is similar to changing frequency. Proceed by setting the amplitude to 2 V.


2.6

Click the Run button in the control bar near the top of the window to begin output the signal.


2.7

Back in the Wavegen instrument, click Stop () to turn off the output signal, leaving the channel enabled and idle. Clicking Stop All will stop all active channels, while clicking “Stop” stops only that particular channel.

Note: An idle channel will still output some amount of voltage, which is determined by the offset parameter by default. Unchecking enable at any point will stop the signal if it is running, disable the channel and set its output voltage to 0V.


3. Wavegen UI Overview

This sections walks through the different controls and features present in the Wavegen instrument

3.1 The Control Toolbar

The control toolbar contains menus and control interfaces used to configure the Wavegen instrument.

File contains options to start a new Wavegen instance, open, or save a Wavegen project for sharing or reuse of the configuration, or export the current Wavegen data as an image or raw data file formatted as a *.csv, *.txt or *.tdms.

Control contains the Run All and Stop All actions.

Channels allows the user to open or close wavegen channels for configuration.

Edit lets the user copy or swap output signal configurations between available channels.

3.2 The Preview Plot

The preview plot displays what the waveform output will be. As the waveform parameters are changed in the configuration panel, the preview plot will update to reflect the changes.

Preview plot graphical settings can be changed by clicking on the Gear icon () in the top right.

3.3 The Configuration Panel

Configuration of the output waveform is done using the configuration panel. There are several different sets of configuration options, which can be selected with the drop-down to the right of the Enable checkbox, labeled “Simple” by default

The “Simple” view accesses the signal type, frequency, amplitude, offset, signal symmetry and phase as drop-down menus. The other panels either allow you to configure the signal parameters in a different manner, or allow for more complicated signal types.

The “Basic” panel allows configuration of the signal parameters that the Simple panel exposes, but does so using sliders. Min and max values can be defined or adjusted via a slider. The usefulness of this panel comes when one is trying to make minute adjustments to the output signal.

The “Custom” panel allows you to build the output signal by combining pieces of pre-defined signals. This is may be done by defining the mathematical representation of the signal using JavaScript syntax, providing the output value of the signal at discrete steps, or by importing a saved waveform file. You may also draw the signal free hand by clicking and dragging in the preview plot of the Custom window.

The “Play” panel allows the user to import then play back a saved file, including audio files. Supported formats are *.csv, *.txt, *.mp3, *.wav, *.wmv and *.avi.

For devices that have a headphone jack, the Wavegen channel outputs are always available through the connector.

The “Sweep” panel is used to play a dynamic signal where the frequency and amplitude changes within a set amount of time. The sweep panel provides all of the same configuration options as the simple configuration panel, with the addition of a linear frequency and/or amplitude sweep.

The “Modulation” panel allows the user to create amplitude- and frequency-modulated signals. The first column defines a high frequency carrier signal, the second column defines another signal that modulates the frequency of signal of the carrier, the third lets modulate the amplitude of the carrier, with a checkbox above each column to enables/disables that modulation.

Next Steps

For more guides on how to use the Digilent Test & Measurement Device, return to the device's Resource Center, linked from Instrumentation page of this wiki.

If voltage values output by the Wavegen are significantly different from expected, please calibrate the device by following the Calibration Guide.

For more information on WaveForms visit the WaveForms Reference Manual.

For technical support, please visit the Scopes and Instruments section of the Digilent Forums.