Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
learn:instrumentation:tutorials:analog-discovery-studio-digital-io [2019/11/20 00:00]
Arthur Brown
learn:instrumentation:tutorials:analog-discovery-studio-digital-io [2020/07/28 17:24] (current)
Arthur Brown
Line 1: Line 1:
-======Using the Digital I/O======+====== Using the Digital I/O (Page has Moved) ​======
  
-{{:​reference:​instrumentation:​analog-discovery-studio:​hardware-reference-manual:​static-io.png?​nolink&​800}} +<WRAP round important 660px> 
- +This guide has been replaced by [[learn/instrumentation/tutorials/waveforms-static-io/start]], and is slated ​to be removed from the Digilent WikiPlease update all bookmarks ​and saved links to the new location.
-===== Introduction ===== +
-This guide explains the use of the //Static I/O// instrument in WaveForms. This instrument is used to interact with a Test & Measurement Device'​s digital input/​output channels through simulated buttons, LEDs, displays, and sliders. +
----- +
-===== Prerequisites ===== +
-  * A Digilent Test & Measurement Device with Digital Input/Output Channels +
-  * A Computer with WaveForms Software Installed +
- +
----- +
-===== Guide ===== +
-==== 1. Opening the Static I/O ==== +
- +
-<WRAP group> +
-<WRAP column half> +
-=== 1.1 === +
-Plug in the Test & Measurement Devicethen start WaveForms ​and make sure the device ​is connected. +
- +
-If no device is connected ​to the host computer when WaveForms launches, the **Device Manager** will be launchedMake sure that the device is plugged in and turned on, at which point it will appear in the Device Manager'​s device list (1). Click on the device in the list to select it, then click the Select button (2) to close the Device Manager. +
- +
-**Note:** //"​Demo"​ devices are also listed, which allow the user to use WaveForms and create projects without a physical device.// +
- +
-**Note:** //The Device Manager can be opened by clicking on the "​Connected Device"​ button in the bottom right corner of the screen (3), or by selecting "​Device Manager"​ from the "​Settings"​ menu at the top of the screen.//+
 </​WRAP>​ </​WRAP>​
-<WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​analog-discovery-studio-oscilloscope:​waveforms-device-manager.png?​600 |}} 
-</​WRAP>​ 
-</​WRAP>​ 
----- 
-<WRAP group><​WRAP column half> 
-=== 1.2 === 
-Once the Welcome page loads, in the instrument panel at the left side of the window, click on the **StaticI0** button to open the //Static I/O// instrument. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​waveforms-instrument-panel:​waveforms-instrument-panel-static-io.png?​nolink&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
-<WRAP group> 
-<WRAP column half> 
-=== 1.3 === 
-Once the //Static I/O// instrument opens, the window contains two rows of Bit I/O digital input and output ports with DIO15-DIO8 in the top row and DIO7-DIO0 in the bottom row all assigned to LED state indicators by default. 
-</​WRAP>​ 
-<WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​staticio_windowdefault.png?​direct&​600 |}} 
-</​WRAP>​ 
-</​WRAP>​ 
----- 
- 
-==== 2. Using the Static I/O ==== 
-<WRAP group> 
-<WRAP column half> 
-//This section walks through setting up the //​StaticIO//​ instrument to display and interact with digital I/O ports and their logic levels. The //Logic Analyzer// will be used to view the state of the output of a virtual button. The //Pattern Generator// will be used to blink a virtual LED.// 
- 
-**Note:** //This guide can be followed using a "​Demo"​ device selected in the WaveForms Device Manager. Doing so allows the user to follow along without having access to an Analog Discovery Studio.// 
-</​WRAP>​ <WRAP column half> 
-</​WRAP>​ </​WRAP>​ 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 2.1 Software Display Setup === 
-This demo does not require any hardware setup but relies on the //Logic Analyzer// and //Pattern Generator// tools in Waveforms. To set up these tools and view them simultaneously,​ follow these steps: 
-</​WRAP>​ 
-<WRAP column half> 
-</​WRAP>​ 
-</​WRAP>​ 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.1.1 ==  
-Click on the Welcome page icon in the upper left corner of Waveforms 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​2019-06-24_13_07_23-window.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.1.2 == 
- Click the //Logic// tool 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_logic.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> ​ 
-== 2.1.3 == 
- Click on the Welcome page again 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_welcome2.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.1.4 == 
- Click the //​Patterns//​ tool 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_patterns.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.1.5 == 
- Click the Docking Windows icon in the upper right corner of Waveforms 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_docking.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.1.6 == 
-Now, the Static I/O, Logic Analyzer, and Pattern Generator tools should all be open and viewed together in the same window with the Logic Analyzer in the top portion of the window, the Static I/O in the bottom left portion of the window, and the Pattern Generator in the bottom right portion of the window. ​ 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​simultaneous_display.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 2.2 Blink a Virtual LED === 
-</​WRAP><​WRAP column half> 
-</​WRAP></​WRAP>​ 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.2.1 == 
-In the //​Patterns//​ tool window, click the "Click to Add channels"​ button and select "​Signal"​. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_patt_sig.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.2.2 == 
-In the "Add Signal"​ window, scroll down "DIO 0", select it, and click "​Add"​. DIO 0 should appear in the //​Patterns//​ tool window. ​ 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_patt_add.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.2.3 == 
-In the //​Patterns//​ tool window under "​Type",​ click the drop down menu to change it to "​Clock"​. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_patt_clk.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.2.4 == 
-In the //​Patterns//​ tool window under "​Parameter 1", click the drop down menu, scroll down to and select "1 Hz". 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_patt_1hz.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.2.5 == 
-In the //​Patterns//​ tool window, click the "​Run"​ button. ​ 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_patt_run.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.2.6 == 
-In the //Static I/0// tool, observe DIO 0 flash at the 1 Hz clock rate set by the //​Patterns//​ tool. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_led_obsv.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 2.3 Toggle a Virtual Button === 
-</​WRAP><​WRAP column half> 
-</​WRAP></​WRAP>​ 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.3.1 == 
-In the //Logic// tool window, click the "Click to Add channel"​ button and select "​Signal"​ from the drop down menu.  
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_logic_sig.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.3.2 == 
-In the "Add Signal"​ window, scroll down to "DIO 1", select it, then click "​Add"​. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_logic_add.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.3.3 == 
-In the //Static I/O// tool window, navigate to the DIO 1 box next to the flashing DIO 0 box. Click on the downward arrow, select "​Button",​ and select the configuration at the top of the list (Released: 0, Pressed: 1). 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_dio1_button.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.3.4 == 
-In the //Logic// tool window, click the "​Run"​ button near the top.  
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_logic_run.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-== 2.3.5 == 
-In the //Static I/O// tool, click on the DIO 1 button and observe the logic level of DIO 1 change from low to high in the //Logic// tool.  ​ 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_logic_obsv.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-==== 3. Static I/O User Interface Overview ==== 
-<WRAP group> 
-<WRAP column half> 
-//This section walks through the various configuration options for the //Static I/O// instrument. These configurations can be used to interact with and display digital signals and circuits either with the previously explored tools in Waveforms or with external digital circuits. However, the scope of this section will be limited to only configuration with brief application discussions.//​ 
-</​WRAP><​WRAP column half> 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 3.1 Group Bus Assignments === 
-By default, the Static I/O tool opens with all the available DIO lines from your Test and Measurement Device in groups of 8, descending from left to right and top to bottom all configured as LED state indicators for each line. To change a particular group, click on the group configuration drop down menu located on the left of the group row. This menu includes: 
-  * Bit IO: (Input/​Output) Last IO, LED, Button, Switch (Discussed further in Section 3.2) 
-  * Slider (Output) ​ 
-  * Progress Bar (Input) ​ 
-  * 7 Segment Display (Input) ​ 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_group.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-==3.1.1 Slider== 
-Selecting "​Slider"​ from the group assignments drop down menu groups those eight DIO lines into an 8-bit binary value output that can be changed by either moving the slider left to right or by entering a value between 0 and 255 in the value text field located to the right of the slider bar. The highest digital line is the most significant bit (MSB) and each digital line will get the corresponding bit value related to the bus value. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_slider.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-==3.1.2 Progress Bar== 
-Selecting "​Progress Bar" from the group assignments drop down menu groups those eight DIO lines into an 8-bit bus input that displays the binary value of the 8-bit bus as a progress bar (increasing from left to right) and displaying the exact value (from 0 to 255) in the text field to the right of the progress bar. The highest digital line is the most significant bit (MSB) and each digital line will get the corresponding bit value related to the bus value. 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_progbar.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-==3.1.3 Seven Segment Display== 
-Selecting "7 Segment"​ from the group assignments drop down menu groups those eight DIO lines into a 7 segment display input. Each of the eight digital lines correspond to one of the segments or the decimal point as seen in the picture to the right. A logic high level illuminates the segment associated with that DIO line.  
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_7seg.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 3.2 Individual DIO Assignments === 
-To change the assignment for an individual DIO rather than an entire group, click on the DIO drop down menu located in the upper left corner of the individual DIO window. This menu includes: 
-  * LED (input) 
-  * Button (input and output) 
-  * Switch (input and output) 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​sio_bitio.png?​direct&​600 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-==3.2.1 LED== 
-The LED input display is the default setting for all DIO lines. This displays the current state of the DIO line: red if logic high, grey if logic low.  
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​staticio.led.png?​direct&​200 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-==3.2.2 Button== 
-Selecting "​Button"​ from the DIO assignment drop down menu provides six options for how the button performs when pressed or released. Button is both an input and output device with two states (pressed and released) with an LED as a state indicator. 0 corresponds to logic low, 1 corresponds to logic high (LED illuminates),​ and Z corresponds to high impedance state which will not trigger the LED indicator and will also not drive the DIO line to a logic low or high level which can be useful if multiple devices are connected to the same line. Image A shows the options for the button behavior and image B shows two examples of buttons in the release state and their corresponding LED indication. 
-</​WRAP><​WRAP column half> 
-A {{ :​learn:​instrumentation:​tutorials:​staticio.button.png?​direct&​200 |}} 
-B {{ :​learn:​instrumentation:​tutorials:​staticio.button2.png?​direct&​200 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-==3.2.3 Switch== 
-Selecting "​Switch"​ from the DIO assignment drop down menu provides four options for how the switch performs. Switch is an input and output device with the output dependent on the switch state selection. Like the Button device, 0 corresponds to logic low, 1 corresponds to logic high (LED illuminates),​ and Z corresponds to high impedance state which will not trigger the LED indicator and will also not drive the DIO line to a logic low or high level which can be useful if multiple devices are connected to the same line. Image A shows the four options for the switch'​s behavior and Image B shows three examples of switches in 0,1,and Z states with their corresponding LED indication. ​ 
-</​WRAP><​WRAP column half> 
-A {{ :​learn:​instrumentation:​tutorials:​staticio.switch.png?​direct&​300 |}} 
-B {{ :​learn:​instrumentation:​tutorials:​staticio.switch2.png?​direct&​300 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 3.3 File Menu === 
-The File drop down menu has four options: 
-  * Open Project: opens a previously saved workspace 
-  * Save Project: saves the current workspace 
-  * Export: exports an image of the current Static I/O tool 
-  * Close StaticIO: closes the Static I/O tool 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​staticio_file.png?​direct&​400 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 3.4 Control Menu === 
-The Control drop down menu contains two options: 
-  * Run: begins the Static I/O tool operation (also accessible by pressing F5) 
-  * Stop: halts the Static I/O tool operation (also accessible by pressing F6) 
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​staticio_control.png?​direct&​400 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 3.5 View Menu === 
-The View drop down menu allows the user to toggle on/off custom name text fields for each DIO line, seen at the bottom of the individual DIO line windows as seen in the picture to the right. Type in the text field to change the DIO line's custom name.  
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​staticio_view.png?​direct&​400 |}} 
-</​WRAP></​WRAP>​ 
----- 
- 
- 
-<WRAP group> 
-<WRAP column half> 
-=== 3.6 Window Menu === 
-The Window drop down menu allows selection of: 
-  * Help menu (also accessible by pressing the F1 key) 
-  * Welcome page (Waveforms) 
-  * Any other Waveforms tool that has been opened from the Welcome page.  
-</​WRAP><​WRAP column half> 
-{{ :​learn:​instrumentation:​tutorials:​staticio_window.png?​direct&​400 |}} 
-</​WRAP></​WRAP>​ 
----- 
-==== Next Steps ==== 
- 
-For more guides on how to use the Digilent Test & Measurement Device, return to the device'​s Resource Center, linked from [[reference:​instrumentation:​start|Instrumentation]] page of this wiki. 
- 
-For more information on WaveForms visit the [[reference:​software:​waveforms:​waveforms-3:​reference-manual|WaveForms Reference Manual]]. ​ 
- 
-For technical support, please visit the [[https://​forum.digilentinc.com/​forum/​8-scopes-instruments/​|Scopes and Instruments]] section of the Digilent Forums. 
  
-{{tag>tutorial analog-discovery-studio}}+{{tag>to-be-removed}}